turgid Posted November 19, 2018 Share Posted November 19, 2018 The drum bearings have gone on my 4 year old Panasonic washing machine. Its sits on the balcony so heat hasnt helped. YouTube suggests its a serviceable item. Panasonic Thailand dont sell them as a separate kit you have to buy the whole drum at 6,000 Bht. Kits are available on the internet but its going to incur duty and be heavy and expensive to ship. Anyone know a place in Bangkok? Suplementary question in case I can't fix it. Whats the best brand of washing machine to buy in Thailand for durability, parts, service and support? It isn't Panasonic Link to comment Share on other sites More sharing options...
Vacuum Posted November 19, 2018 Share Posted November 19, 2018 If you can't find a 'bearing shop', you could try to re-grease the bearings. Link to comment Share on other sites More sharing options...
giddyup Posted November 19, 2018 Share Posted November 19, 2018 We've had out LG 11 kilo machine for over 8 years, gets used every day, never missed a beat. Link to comment Share on other sites More sharing options...
lopburi3 Posted November 19, 2018 Share Posted November 19, 2018 Wife will only use top loaders and previously had many National (Panasonic) units that never lasted long. Bought 13kg Hitachi in 2006 and still working fine (this for family of nine with several loads most days). Have expected issues as it can be noisy and take a few tries getting load balanced for high speed spin; but holding up well. Link to comment Share on other sites More sharing options...
fruitman Posted November 19, 2018 Share Posted November 19, 2018 Miele is the best and affordable in thailand. Link to comment Share on other sites More sharing options...
moontang Posted November 19, 2018 Share Posted November 19, 2018 Overloading is the killer; not the heat. Many laundry areas are outside here, and in Phoenix, which sees 50c...One thing I noticed is folks don't set up the discharge line correctly, as prescribed in the manuals. It needs to go up, then down, not just down...otherwise, you are spinning extra water weight. Link to comment Share on other sites More sharing options...
fruitman Posted November 19, 2018 Share Posted November 19, 2018 42 minutes ago, moontang said: Overloading is the killer; not the heat. Many laundry areas are outside here, and in Phoenix, which sees 50c...One thing I noticed is folks don't set up the discharge line correctly, as prescribed in the manuals. It needs to go up, then down, not just down...otherwise, you are spinning extra water weight. I thought that line goes up and then down for the siphon against smell from the drain... Link to comment Share on other sites More sharing options...
moontang Posted November 19, 2018 Share Posted November 19, 2018 It is to prevent siphoning of water. Gas would be vented. Link to comment Share on other sites More sharing options...
fruitman Posted November 20, 2018 Share Posted November 20, 2018 7 hours ago, moontang said: It is to prevent siphoning of water. Gas would be vented. So what do you mean with spinning extra water weight in the washingmachine if the discharge hose goes straight down from the machine? If the machine starts pumping water out it will just pump it into the discharge hose, no matter if that goes up or down isn't it? And it will continue pumping until the sensor tells the machine to stop (when it's empty). So how does that influence the machine spinning extra water weight inside Link to comment Share on other sites More sharing options...
moontang Posted November 20, 2018 Share Posted November 20, 2018 GE manufactured several hundred million washing machines, and their website says it needs to go up 30 inches from the ground to prevent siphoning of water. It is important for the drain to be optimized, or you will not get optimum performance. Link to comment Share on other sites More sharing options...
mogandave Posted November 22, 2018 Share Posted November 22, 2018 NTN Bearings has a big outlet on the Trad road (I think) between Outer Ring Road and HomePro on the left hand side (going toward HP) Link to comment Share on other sites More sharing options...
mogandave Posted November 22, 2018 Share Posted November 22, 2018 I think the drain needs to be high to keep water in washer... Link to comment Share on other sites More sharing options...
fruitman Posted November 23, 2018 Share Posted November 23, 2018 10 hours ago, mogandave said: I think the drain needs to be high to keep water in washer... I guess so...maybe there's no electric valve in the discharge line? Only a pump.... Link to comment Share on other sites More sharing options...
mogandave Posted November 23, 2018 Share Posted November 23, 2018 I guess so...maybe there's no electric valve in the discharge line? Only a pump.... Lay the hose on the floor while it’s running and find out....I imagine it has a valve that opens when the pump comes on, but in the event the drain backs up or the valve gets stuck it can’t siphon drain water back into the washer. Link to comment Share on other sites More sharing options...
moontang Posted November 24, 2018 Share Posted November 24, 2018 It's a washing machine, not a bathtub. Link to comment Share on other sites More sharing options...
mogandave Posted November 24, 2018 Share Posted November 24, 2018 It's a washing machine, not a bathtub.Why would someone need new bearings for a bathtub? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.